fshenkin94
Member
Anyone know how I can set up a jig to route a curved line in a board. I may have to make 2 passes with the router to get it wide enough, so it has to be something that I can repeat.
Thanks
Thanks
Routing a curved line
- Thread starter fshenkin94
- Start date
Signed-In Members Don't See This Ad
Signed-In Members Don't See This Ad
PTownSubbie
Member
Is it a simple arc in a circle pattern? If so, you can just use a circle cutting jig for your router bottom.
If this is the case, let us know and someone will explain how to set it up.
If this is the case, let us know and someone will explain how to set it up.
kirkfranks
Member
If the suggestion above will not work for your application you can make a template and use a pattern bit. They have a bearing to follow your template on the top and basically a straight cutting bit on the bottom end.
Third group down on this page.
http://www.mlcswoodworking.com/shopsite_sc/store/html/smarthtml/pages/bt_flush.html
Third group down on this page.
http://www.mlcswoodworking.com/shopsite_sc/store/html/smarthtml/pages/bt_flush.html
Steve Busey
Member
WFS (what Fred said...)
Google (or Bing!) on "router circle cutting jig". It can be as simple as a piece of scrap 1/4" plywood screwed on the bottom of your router, then make your pivot point(s) as far away as you need for your curve(s).
Google (or Bing!) on "router circle cutting jig". It can be as simple as a piece of scrap 1/4" plywood screwed on the bottom of your router, then make your pivot point(s) as far away as you need for your curve(s).
VisExp
Member
If it is a circle then a circle cutting is easy to make and use.
http://www.woodworkingtips.com/etips/etip102000sn.html
If it is not a circle you need to draw out the pattern on a piece of plywood. Cut the pattern using a bandsaw or jigsaw. Tape the pattern to the workpiece with double sided tape or clamps if you have the access. You can then either use the bit Kirk referred to or you can just use a straight bit in conjunction with a router template guide.
http://www.amazon.com/Porter-Cable-...ref=sr_1_1?ie=UTF8&s=hi&qid=1245374381&sr=8-1
If you use the straight bit/template guide combination you will need to allow for the thickness of the template guide and the difference between the ID of the guide and the diameter of the router bit.
You also mentioned that the groove you need to cut might be require two passes. I don't think moving the template will work. The geometry of moving a curve will not give you a groove with two parallel sides. You would need to cut a template for both sides of the groove and then run the router up one side of the template and down the other side.
Whichever method you use a plunge router would be easier, unless you are able to come in from the side of the workpiece.
http://www.woodworkingtips.com/etips/etip102000sn.html
If it is not a circle you need to draw out the pattern on a piece of plywood. Cut the pattern using a bandsaw or jigsaw. Tape the pattern to the workpiece with double sided tape or clamps if you have the access. You can then either use the bit Kirk referred to or you can just use a straight bit in conjunction with a router template guide.
http://www.amazon.com/Porter-Cable-...ref=sr_1_1?ie=UTF8&s=hi&qid=1245374381&sr=8-1
If you use the straight bit/template guide combination you will need to allow for the thickness of the template guide and the difference between the ID of the guide and the diameter of the router bit.
You also mentioned that the groove you need to cut might be require two passes. I don't think moving the template will work. The geometry of moving a curve will not give you a groove with two parallel sides. You would need to cut a template for both sides of the groove and then run the router up one side of the template and down the other side.
Whichever method you use a plunge router would be easier, unless you are able to come in from the side of the workpiece.
Last edited: