Peppermill making: Advices and lessons learned please!

Signed-In Members Don't See This Ad
See more from CharlesH

CharlesH

CharlesH

Member
Joined
Oct 6, 2009
Messages
600
Location
Canada, Quebec, Laval
Hey guys,

Just looking around to start making some peppemills. I have bought Ted Sokolowski DVD and it is fantastic.

I am wondering where I can find the drill bits required. I am interested in the CrushGrind kit. The bits I will need are: 15/16", 1-1/16", 1-9/16" and 1-3/4.

I noticed Wood Turner's Catalog is out of stock on some of those bits and in my experience the bits they carry are not up to my standards in terms of quality, at least for the pen kits!

Any comments and advices welcomed! :)

Charles
 
Signed-In Members Don't See This Ad
Last edited:
I picked up a titanium coated 16 piece bit set (1/4" to 2 1/8") from Harbor Freight for 39.00. They work well for the price.
 
Bowl Slinger said:
I picked up a titanium coated 16 piece bit set (1/4" to 2 1/8") from Harbor Freight for 39.00. They work well for the price.
Click to expand...

Trouble is, you need 1 & 1/16 which is rarely in those sets. After 1", they go to eighth inch increments.

I found a set years ago that has only the sixteenths from 1 & 1/16 through 2.5"--with both sets, you got it made!!:biggrin::biggrin::biggrin:
 
I plan on making mills in really hard woods like cocobolo and African Blackwood. Hopefully someone will point me where I buy quality bits. :-P

C

Sent from my Samsung Galaxy S2.
 
I make a lot of the crush/grind pepper mills... I get all of my drill bits from the local Woodcraft... at about $10 each, I can use one until it gets dull and then just replace it... also I don't follow all of the instructions... I don't use but 3 of the bits.. I drill all the way through my mills with the 1 9/16 bit and don't use the 1 1/16 at all. To keep the top from flopping around too much, I put a short tenon on the top portion that fits down inside the body at the top.
 
For the crush grind mechanism Woodturners suggest a 1-9/16" drill bit and from the tech plans from Crush Grind they say 38mm which is 1-1/2".

Anyone has a though on that?

Charles
 
My dad has done probably 100+ peppermills. He has uses a colt bit for the really long hole, the 1-1/16 hole. It works really good, compared to other bits. But you need a THICK extention shaft when drilling these holes, or else they will walk...No matter what bit you have, even colt bits, will not work cut perfectly. There will be little cocobolo cakes everywhere.
Another suggestion is to use enduro finish. My dad recently started to use this finish. I tried it for pens, and it took to long. But it is way more shinier, and you can build it up and sand it down just like ca.
 
Charles

Suggest you look at everything Lee Valley has to say and offer here Drill Bits - Lee Valley Tools - Woodworking Tools, Gardening Tools, Hardware Supplies

Have made (rather am in the process of making ) both crush grind and conventional mills . The crush grind components have 6 ribs molded on the outside of the grinding unit . They appear to be designed to be a push interference fit in a 1 9/16 hole , hence that size on the one set of instructions . The set calling for 1 1/2 inch recommends grinding the ribs off , which is what I have done . My reason for doing so was that I didn`t have a 1 9/16 .

The key to a smooth operating mill is to have the hole that the grinder sits in concentric with the hole in the cap . That is a bit easier said than done with Forstner or saw tooth bits as you drop down from 1 1/2 to 1 1/16 to 7/8 .

Make sure you drill at least the two largest holes before turning . It is more difficult to keep concentricity if you drill afterwards .

Please don`t think that I`m an expert on these things . They have contributed to an increase in my vocabulary though .
 
I will say that I have made many mills and the best bit I have found is made in Germany and cost many dollars but is worth every one of them. Probably from CSA but not sure.
 
Don Wade said:
I will say that I have made many mills and the best bit I have found is made in Germany and cost many dollars but is worth every one of them. Probably from CSA but not sure.
Click to expand...

I ordered the Colt MaxiCut bits, they are made in Germany. ;-)

C

Sent from my Samsung Galaxy S2.
 
You must log in or register to reply here.
Back
Top Bottom