A better sanding

Signed-In Members Don't See This Ad
G

Gabericks

Member
Joined
Oct 12, 2019
Messages
61
Location
South Carolina
Okay I give up. I'm tired of buying cheap sandpaper from Lowe's and sanding a few pen blanks before throwing a small sheet away.

Does anybody have a recommended sanding system beyond paperback, cheap sandpaper?
Thanks
 
Signed-In Members Don't See This Ad
I use Mirka abranet, micro mesh, Yorkshire grit, and a couple other methods depending on weather i am working with wood or not wood, Wood Is Abranet, Yorkshire, then friction polish if I'm going natural finish. If its CA then I wet sand with micromesh to 12,000 grit, then I use a 20,000 and 30,000 diamond paste. There are a ton of different methods though
 
If you are working with resins, I might suggest looking in your local auto parts store or automobile paint supply stores for better grade sheets. The papers they typically sell are high grade, commercial level stuff that has good consistency of grits. You will pay a bit more, but the value is there. Most all of the wet sanding papers I use I purchase there, including the polishing paste I use. Cut the sheet into small pieces to use.
 
EricRN said:
The 3m cubitron is the absolute best in my view.
Click to expand...
I should have added that I really like micromesh pads for resins. My method is—cubitron from 80 or 100 grit (depends on how good mg turning is) through 600 grit; then micromesh through all colors; then novus coarse polish, novus fine polish, and then the novus cleaner or Renn wax. Thats for plastic.

For wood, I'll use doctors pens plus finish in place of the novus, and then finish with Renn wax.
 
I did a deep dive on sandpaper a couple months ago and found this site recommended in another thread here:

SandWet™ Wet/Dry Tufbak® T461, Blue-Bak T414, Black Ice™ T214/T401

www.onlineindustrialsupply.com www.onlineindustrialsupply.com

I'm using the Norton Blue-Bak Silicon Carbide paper for all grits except 800 (which they only have in Aluminum Oxide) and for 800 I tried the Black Carbon brand, which is still good but a bit thinner backing than the Norton Blue-Bak.

www.onlineindustrialsupply.com

BlackCarbon Wet or Dry Silicon Carbide Sandpaper Sheets

BlackCarbon Wet or Dry Silicon Carbide 9" by 11" Sandpaper Sheets. Specially treated waterproof paper can be used wet for automotive sanding, and dry on wood for quality finishing. Available grits: 60 to 2500. Sold in packs of 50 sheets.
www.onlineindustrialsupply.com www.onlineindustrialsupply.com
 
A couple recommends... sorry if these seem obvious:
  • Start with the finest grit you can.
    • Removing the scratches from coarser grits can be very time consuming.
    • I never use anything below 400 grit, and typically start with 600 grit.
  • Do NOT skip grits.
    • Removing the scratches from 120 grit with 400 grit will take an eternity
  • Before switching to the next finer grit, sand lengthwise with the machine off
 
Gabericks said:
Okay I give up. I'm tired of buying cheap sandpaper from Lowe's and sanding a few pen blanks before throwing a small sheet away.

Does anybody have a recommended sanding system beyond paperback, cheap sandpaper?
Thanks
Click to expand...
"what everyone else said above"....

Along with that, sandpaper is meant to be discarded after a certain point. The brand may allow you to use one piece a little longer but nothing is going to be perfect.

I have no particular reason why I do things this way but I do.... I have a 5 pack of sandpaper rolls in 1 inch wide strips that I use. I purchase it from Woodcraft or Exotic Blanks. EB sells refills for the rolls. I typically use the sandpaper on wood blanks.

I also have Abranet sanding mesh in the same grits and find myself only using that on resins and plastics. I have used the Abranet on both types of blanks and migrated back to sandpaper for the wood blanks. I cut the abranet into 1 inch wide strips from the long/wide pieces I get from EB and then use a sharpie to write the grit rating on the paper so I can put everything in the correct order if I accidently drop them. Yes, that was learned from experience.

I am downright terrible, possibly horrible, about using the Abranet too long. Using the sandpaper I use a fresh strip that's 2 or 3 inches long for each grit for each pen. I really love how the Abranet works and sheds sanding dust.

I really like using the strips because it focuses me on how and what I'm sanding rather than dealing with a piece of sanding material that's too big for what I'm doing.

I really should just buy rolls of Abranet and haven't done it.
 
I use the rolls from 150 to 600 for wood. Also stumbled across 1000 and 4000 sandpaper on a closeout shelf at Michael's; both are Craftsman FYI. For synthetics, I turn with carbide, then to a skew, 500 grit, 1,000 grit. Then MM and Hutt plastic polish.
I cut sandpaper with cheap scissors from Harbor Freight @$1.99 a pair. Find I have good luck with strips rather than sheets. Have two or three pair of scissors in the shop and storage building.
 
Gabericks said:
Okay I give up. I'm tired of buying cheap sandpaper from Lowe's and sanding a few pen blanks before throwing a small sheet away.

Does anybody have a recommended sanding system beyond paperback, cheap sandpaper?
Thanks
Click to expand...
Before you go buying super expensive abrasive sheets I have a few tricks that may resolve your dilemma.

1. You can use one of those rubbery sticks that are used on belt/circular sander to clear the wood swarth from the grit side of the sanding paper. I've done that for years and it will 'rejuvenate' the grit side so it can be used a time and again. Yes, eventually the grit just breaks down but most of the time is just gets so fouled with swarth that it cannot cut any more.

2. Something else I do is drag the grit side of the paper on the outside of either my jeans or my shirt when I am into a project and dont want to step aside to get the stick, and that will clear the swarth also. Obviously it will dirty your clothes but I'm sure you aren't wearing your Sunday best to work in the shop. And before anyone steps up and says, you'll wear your clothes doing that....really? You do it when the sandpaper isn't cutting as well as it should, not after every stroke. Yes, I've used this method on the micromesh pads and it works well.

With that being said, I've been using the color coded rolls but they are no longer available so I'm not going to link them but I just bought THIS set of rolls and started using the 150grit on a new project and it seems to hold up pretty well. Of course I use method number 2 above to refresh the grit.
 
Mortalis said:
Yes but, I cant seem to find the dammed toothbrush when I want it. 😜
I can always find my pants or shirt.
Click to expand...
I save mine. Have at least half dozen in various places- lathe has two, drill press, bandsaw, table saw. Another half dozen in a canister on a cabinet. Glad you can find your pants. I'm getting a mental picture. :oops:
 
You must log in or register to reply here.
Back
Top Bottom