Hi everyone! Can I drill my pen blanks with my lathe since my drill press won't drill the blanks all the way thru? I'm just starting out and having a great time turning different things. This forum is awesome too with a lot of info. Thanks, Tim
Drilling Blanks
- Thread starter ts8181
- Start date
Signed-In Members Don't See This Ad
Signed-In Members Don't See This Ad
butchf18a
Member
Yes you can
Boz
Member
I only drill on the lathe. Much more accurate than any drill press. You will need a chuck to hold the brill bit. You will need one with the correct taper to fit on your tail stock. The first one I bought used a key to tighten the chuck. That was a bit of a pain so I traded up to a keyless one much better. Then you need a vice that fits on the head stock. I have one for square blanks and a collet set for round ones. The concept is the blank turns and the drill bit does not. You advance the drill bit forward into the spinning blank using the quill on the tail stock. Every 1/4 inch or so pull the bit back out to get all the shavings out. Some here on this forum have not done this and have had the drill bit bind up in the blank. Turn the blank at a low to medium speed. Too fast and you may get a heat build up that may damage the blank. Once you have the correct tools drilling blanks on your lathe is as easy as pie.
Paul in OKC
Member
My first drill press had a short stroke as well. I would drill as far as it would go, stop the motor, slide a 1 by 4 under the vise sliding up the bit, and finish from there. A pain, yes, but it worked.
And yes you can drill on the lathe as many do.
And yes you can drill on the lathe as many do.
wildanessdude
Member
I've just recently started making pens and I drill all my blanks using this:
NOVA Pen Plus Jaw Set
I HIGHLY recommend these jaws if want accuracy when drilling blanks. You do have to buy a chuck too but they are nice to have anyway.
NOVA Pen Plus Jaw Set
I HIGHLY recommend these jaws if want accuracy when drilling blanks. You do have to buy a chuck too but they are nice to have anyway.
healeydays
Member
I too only drill blanks on my lathe using a Nova Pen Plus Jaw set. Never had an issue.
George417
Member
I also use the pen jaw set on my chuck. Only way to do it now.
Lenny
Member
I would recommend you get a collet chuck. While the jaw chucks work, a collet chuck is way more versatile. In the long run you will be glad you did!
so.. with the collet chuck method - I assume you need to round down the blank first so it fits the collet? Seems like this would require an extra step and swap out of lathe tools unless you have a dedicated lathe for this? Lots of ways to tackle turning a pen!
jroach21
Member
Russianwolf
Member
Yes, it does require an extra step, BUT it is a beneficial step.
I round all my blanks first between centers. Why?
Because it gives a much better indication of what is inside the blank. Allowing me to make better decisions on where to cut and see if there are any problem areas.
Also, wood blanks are rarely square and straight. Center drill the ends and turn between centers and suddenly they are uniform and easier to work with.
I know some that also do their segmenting on round blanks because of the uniformity can easily be off on square blanks.
Sabaharr
Member
I had the same experience as jroach21 only mine didn't end as nicely as his. I got hit on my left forearn by the chuck when a segmented blank shattered from the torque of a lose freespinning chuck. I pulled back the tailstock to clear shaving from the bit and the bit locked itself into the blank. I thought it had broken my arm at first but further examination revealed a big knot, swelling, and bruising. I got lucky on that one and will not let that happen again. I think about it every time I draw back that tail stock. Experience is as much about knowing what NOT to do as it is know what TO do.