CA finish on stabilized blanks
- Thread starter gspalding
- Start date
Signed-In Members Don't See This Ad
Signed-In Members Don't See This Ad
mrcook4570
Member
YES!
NO!
thewishman
Member
George, the air in the blank was replaced (for the most part) with resin in the stabilization process. There is still a much larger portion of wood in the blank and that will be slightly shiny after sanding and polishing. If you want a glossy finish, you'll still need to apply a finish.
GaryMadore
Member
The stabilized wood I have turned was just like turning plastic. For all intensive purposes, it was no longer wood and didn't need (nor would it "hold") a finish.
Sand and polish.
Cheers!
Gary
P.S. My stabilized blanks were bought from Lee Valley - YMMV, and that's the extent of my experience.
Sand and polish.
Cheers!
Gary
P.S. My stabilized blanks were bought from Lee Valley - YMMV, and that's the extent of my experience.
Rick_G
Member
Like Stan and Chris said. I always apply a CA finish to stabilized blanks. Never been able to get a consistent finish without it.
mrcook4570
Member
Finish it or don't finish it, the choice is yours. But the ultimate test is putting it to use and handling the pen everyday. Without a finish, a stabilized blank will buff out to a nice sheen. However, it will NOT maintain that sheen with frequent use/handling and it will NEVER approach the gloss of a properly done CA finish.
DurocShark
Member
leehljp
Member Liaison
Stabilizing a blank does not replace the wood! Nor does it turn wood to plastic. the wood is still wood. Have you ever done a money blank? It is 95% PR. Yet when turned, the shredded money makes dull spots where it comes to the edge of the turned blank. Unless one want the dull spots, it should be finished with a finish such as CA, lacquer, poly etc.
Listen to Mr. Cook. You don't have to do finish it with CA as that is your choice. It won't destroy or hurt the blank to finish with CA at all.
Funny that this should come up now - I turned the first stabilized blank in almost a year tonight. Going to Tokyo tomorrow and got a request for a "blue" pen. I picked out a dyed and stabilized blank from Ernie at BearToothWoods. I debated a minute after carrying it through 12000 MM and decide it sure would look better with CA, and sure enough it did.
Listen to Mr. Cook. You don't have to do finish it with CA as that is your choice. It won't destroy or hurt the blank to finish with CA at all.
Funny that this should come up now - I turned the first stabilized blank in almost a year tonight. Going to Tokyo tomorrow and got a request for a "blue" pen. I picked out a dyed and stabilized blank from Ernie at BearToothWoods. I debated a minute after carrying it through 12000 MM and decide it sure would look better with CA, and sure enough it did.
Rifleman1776
Member
Depends on the wood, the stable material and method used to do the stable. Some won't need it, some might. You might want to just turn the blank to round and experiment before doing the final turning.
S
spiritwoodturner
Guest
I'll chime in here with the need for a finish. It may look good with just a polish when done, but it won't stay that way. I put CA on stabilized blanks all the time, and it works great.
I have to include that there is definitely a difference between the blanks I stabilize and the pro done ones. It's not enough for me to want to pay 5 bucks for it, but they do finish differently. I have done both and still believe they both need a finish, if you want them to stay looking nice.
Dale
I have to include that there is definitely a difference between the blanks I stabilize and the pro done ones. It's not enough for me to want to pay 5 bucks for it, but they do finish differently. I have done both and still believe they both need a finish, if you want them to stay looking nice.
Dale