Looking to start making acrylic blanks - Page 2 - International Association of Penturners
     International Association of Penturners
Pens for Service Members
 
Support The IAP

Go Back   International Association of Penturners > Community Forums > Blank Making > Casting & Stabilization
  Forgot Password
Register FAQ Members List Search Today's Posts Mark Forums Read
Casting & Stabilization Making your own blanks & stabilizing wood blanks.


Logged on members can hide ads!

Welcome to penturners.org!

You've found the home of The International Association of Penturners. You are currently viewing our site as a guest, which gives you limited access to view discussions, photos, and library articles.

Consider joining our community today. You'll have full access to all of our content, be able to enter our contests, find local chapters near you, and post your questions and share your experience with our members all over the world.

Membership is completely free!!

If you have any problems with the registration process or your account login, please contact us.

Reply
 
LinkBack Thread Tools Display Modes
Old 02-19-2013, 10:24 AM   #11 (permalink)
 
BSea's Avatar
 
Join Date: Dec 2009
Location: Little Rock, Arkansas
Posts: 4,545
Photos: 40

Default

Quote:
Originally Posted by Mack C. View Post
Did you happen to notice the original question was put forth in Feb. 2011?


I had to laugh at this. The thing is when someone is doing research on something, they sometimes keep digging deeper & deeper into threads that link to past threads. Then they respond to threads sometimes several years old. It happens . . . . . .DAMHIKT
__________________
Bob

Central Arkansas IAP Chapter Member

Last edited by BSea; 02-19-2013 at 10:27 AM.
BSea is offline   Reply With Quote Top
Old 02-19-2013, 10:39 AM   #12 (permalink)
 
HamTurns's Avatar
 
Join Date: Jul 2012
Location: Madison, Wisconsin, USA
Posts: 274
Photos: 0

Angry Oooops

OOOps -


Just after I hit "post" I remembered that I was reading the old posts and should not have replied.

So I just went back and was going to delete that post, I was too slow.

Sorry for replying to an old post.

Tom
HamTurns is offline   Reply With Quote Top
Old 02-19-2013, 10:41 AM   #13 (permalink)
 
Displaced Canadian's Avatar
 
Join Date: Aug 2009
Location: Seattle, WA
Posts: 2,927
Photos: 34

Default

About 3 years ago there was a post titled I hate CA and after the initial conversation ended about once every month or 2 someone would post on it and bring it back to life.
Displaced Canadian is offline   Reply With Quote Top
Advertisement
Old 02-19-2013, 11:27 PM   #14 (permalink)
 
its_virgil's Avatar
 
Join Date: Jan 2004
Location: Wichita Falls, TX, USA.
Posts: 6,816
Photos: 74

Default

...and wineWorkerAdamC hasn't been active since just after the original post that started this thread. I guess our library suggestions didn't suit him.i guess we all should have retyped our articles in his thread.
Do a good turn daily!
Don

Quote:
Originally Posted by Mack C. View Post
Quote:
Originally Posted by HamTurns View Post
Hi Adam -

I've just finished my 6th casting using Alumilite (and ordered 4 more gallons with the IAP vendor discount during the 2013 BASH!).

I had the same questions you had, and a lot more.

The fine folks that are steering you towards the library are right on target, there you will find ALL of the information you'll need to get started.

I have read everything I could find in the library and it was more than enough information to get me to where I am now.

As mentioned before, another excellent information resource is this forum, I'm on page 62 now. It's taken some time to read all of this, but I have learned something new on every page.

Tom
Did you happen to notice the original question was put forth in Feb. 2011?
__________________
Don Ward aka its_virgil
Wichita Falls, Texas
www.RedRiverPens.com
www.RedRiverPens.com/articles (pen stuff I've written)
its_virgil is offline   Reply With Quote Top
Related Content
Logged on members can hide ads
Reply

Bookmarks

Tags
acrylic , blanks , polyresin , pr

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


All times are GMT -5. The time now is 01:19 AM.

Powered by vBulletin® Version 3.7.6
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0

Content Copyright © 2003-2016 by Penturners.org, LLC; All Rights Reserved
Terms Of Service   Acceptable Use Policy